DIY-Calculator Hardware:Hardware Project

Project status (28.Nov.2006):

A new cycle of prototyping started.

After very careful inspection of first prototypes, at least as far this was possible, all layout changes are made for the new prototyping cycle - hopefully this time we'll have more luck...

Schematics:

• FPGA Board Schematics

Layout:

• FPGA Board Layout

Project status (24.Nov.2006):

Assembled FPGA board (very first version) finally appeared.

populated FPGA Board

Good and bad news...

Good news first: We've got the board finally - almost everything works as supposed.

Now the bad news: FPGA does not work! I've made two mistakes - T1 (in JTAG chain) has drain and source the wrong way around - this is not really bad because I can fix it just for these three samples. But the second one is quite fatal - VCCAUX on FPGA should be wired to 3.3V instead of 1.2V. As those voltages are on inner layers and under the BGA, there is no way to get this fixed. I could manage to disconnect it from 1.2V but FPGA doesn't start configuration when one of the voltages is out of specs.
Anyway, attached picture looks nice - I'll put down my "Picasso" at home and hang this up instead - it's almost as expensive :-)

Project status (16.Nov.2006):

Work on FPGA Board revision is finished.

FPGA Board screenshot

Schematics:

• FPGA Board Schematics

Layout:

• FPGA Board Layout

Thanks to Johannes' genious SPI controller, userdata can be permanently stored in the sparespace of FPGA's Serial Flash. This obsoletes all the PROM/RAM socket stuff. A 128kx8 SRAM has been added instead. At boottime, userdata is restored from SPI to RAM and the Monitor starts execution. Nowadays, 128kx8 SRAM's are the smallest available. This is actually twice as much the DIY CPU can address. Therefore an extra address line (A16) is added and can be used for future expansion.

Project status (15.Nov.2006):

Work on keypad revision is finished.

Keypad screenshot

Schematics:

• Keypad_Schematics

Layout:

• Keypad_Layout

After successful tests with prototype, we now changed throughhole components to SMT. Silkprint was added and 16 spare signals from FPGA board are now tied to testpoints, for better usability as a generic FPGA prototyping environment. Circuitry for switching LCD backlight was added (see new schematics).

Due to very poor availibility of the previously planned LCD Display, we decided to choose a "more common" 2x20 type. This display is manufactured by a lot of different vendors. Later, the LCD controller inside the FPGA, will be extended to adress the extra line - most probably a new I/O port for the CPU will be assigned for this purpose, to maintain compatibility to the Virtual DIY Calculator.

Redesign of FPGA board is in progress...

Project status (11.Nov.2006):

During the past weeks a lot of things happened at the software side (see Upload_Utility_Project). This happened just in time, since we expect the first pieces of the real DIY Calculator hardware for next week. So stay tuned, this section will soon have great news and exciting pictures!

Project status (9.Oct.2006):

New LCD module tested and integrated. The originally planned 20x1 LCD module is hard to get, so we evaluated additionally 20x2 types (this mainly has impact on the mechanical hardware design).

Project status (31.Aug.2006):

Testing sensor pads

~3uS skew

Test of sensor keypad was successful. Here are the photos

Project status (13.Aug.2006):

Prototype PCB layout completed. Here are the "final" schematics:

• Keypad_Schematics
• FPGA_Schematics

keypad mechanics:

• Keypad_Mechanics

and the layout:

Bare FPGA Board

Keypad prototype

• Keypad_Layout
• FPGA_Layout

Test of sensor keypad is in progress.

Project status (7.Aug.2006):

We decided to separate the functionality into two PCBs: the FPGA with surrounding components and the sensor keypad. This gives even more flexibility for different I/O modules. Here are the updated schematics:

• Keypad
• FPGA

Project status (19.Jul.2006):

schematics completed, PCB layout work started

• preliminary Schematics